Usually urgent, not an emergency

Maytag Washer: Leaking Water

Most often a worn door boot or gasket, a loose hose clamp, or a failing drain-pump seal. Add a photo of your Maytag Washer in the box below: the Triage Profile says what it is, how urgent it is, and who to call.

Show us the washer.

Snap a photo — see what it is, how urgent, who to call. One photo of the problem. fixRAgent reads it and gives you a Triage Profile.

Phone photo of a front-load washer with water spreading across the floor in front of it
TODAY3 of 3 reads agreed
Washing machine
Call an appliance technician
A real Triage Profile from this photo, read by fixRAgent on 9 Oct 2026. Open it ›

Or start with a sentence

In the next five minutes

Safe first steps, before the call. Nothing here needs a tool.

  1. If water is near the plug or outlet, don’t touch them. Switch off the washer’s breaker first. Don’t stand in water to reach the breaker panel; if the panel is wet or you’d have to stand in water, leave it and call.

  2. Then turn off the washer’s hot and cold water valves, if you can reach them without moving it.

  3. Take a photo of the washer, the water and any code on the display, without opening anything.

Everything else about this problem

Is it an emergency?

Is a Maytag washer leaking water an emergency?

Usually urgent, not an emergency. Turn off the water to it and unplug it or switch off its breaker, then soak up standing water. If water is reaching outlets or cords, switch off the breaker before touching anything; water coming through a ceiling is an emergency.

Symptoms & causes

Your Maytag washer is leaking water, often evidenced by puddles forming on the floor around or under the appliance, which can indicate a breach in the water containment system. Common leak points include the drain hose, water inlet valve, pump, or the main tub seal, each leading to distinct patterns of water accumulation. These leaks are typically caused by worn-out components, loose connections, clogs, or physical damage to hoses and seals over time.

Tools & parts

Essential tools for checking and repairing a Maytag washer leak include basic screwdrivers (Phillips and flathead), pliers, a flashlight, and a bucket for catching water. Specific replacement parts might include a new drain hose, a water inlet valve, or a replacement drain pump, depending on the leak source. A multimeter can also be useful for checking electrical components, and plumber's tape or sealant may be needed for connections.

Safety first

Always disconnect the Maytag washer from its power source by unplugging it from the wall outlet before attempting any inspection or repair to prevent electrical shock. Turn off the hot and cold water supply valves located behind the washer to stop the flow of water into the machine. Be cautious of sharp edges on internal components and potential residual water that could cause slips or further electrical hazards.

When to call a pro

You should call a professional technician if the leak source is not easily identifiable after checking common culprits, or if the repair involves complex internal components like the main bearing or outer tub. A professional is also needed for issues related to the Maytag control board or motor, which require specialized testing tools and expertise. Extensive disassembly, such as replacing a cracked outer tub, is typically beyond a DIY repair and best handled by a certified Maytag appliance repair specialist.

Questions people ask

Why is my Maytag washer leaking from the front?

If your Maytag front-load washer is leaking from the front, the most common culprit is a damaged or dirty door boot gasket (the rubber seal around the door opening). Inspect it for tears, cracks, or residue buildup that prevents a tight seal, and clean or replace it as necessary.

What causes a Maytag washer to leak from the bottom?

Leaks from the bottom of a Maytag washer often point to issues with the drain pump, its housing, or the hoses connected to it. It could also be a failure of the main tub seal or a loose connection at the water inlet valve, allowing water to drip down.

How do I stop my Maytag washer from leaking?

To stop a Maytag washer from leaking, first identify the source by carefully observing where the water appears. Tighten any loose hose connections, inspect the drain hose for cracks, and check the door seal for damage or debris, replacing any faulty parts promptly.

Related problems
fixRAgent

What it is, how urgent, who to call

Add a photo of your Maytag Washer in the box at the top. The Triage Profile says what it is, how urgent it is, and who to call.

Get started